| Project/Area Number |
14550125
|
|---|
| Research Category |
Grant-in-Aid for Scientific Research (C)
|
| Allocation Type | Single-year Grants |
|---|
| Section | 一般 |
|---|
| Research Field |
設計工学・機械要素・トライボロジー
|
|---|
| Research Institution | Kobe University (2004)
神戸商船大学 (2002-2003) |
|---|
Principal Investigator |
FUKUOKA Toshimichi Kobe University, Faculty of Maritime Sciences, Professor, 海事科学部, 教授 (00116279)
|
|---|
| Co-Investigator(Kenkyū-buntansha) |
TAKAKI Tomohiro Kobe University, Faculty of Maritime Sciences, Research Associate, 海事科学部, 助手 (50294260)
|
|---|
| Project Period (FY) |
2002 – 2004
|
| Project Status |
Completed (Fiscal Year 2004)
|
| Budget Amount *help |
¥4,000,000 (Direct Cost: ¥4,000,000)
Fiscal Year 2004: ¥800,000 (Direct Cost: ¥800,000)
Fiscal Year 2003: ¥1,000,000 (Direct Cost: ¥1,000,000)
Fiscal Year 2002: ¥2,200,000 (Direct Cost: ¥2,200,000)
|
|---|
| Keywords | Pipe flange / Gasket / Sealing performance / Three-dimensional FEM / Bolt clamping force / Flange rotation / ジョイントシートガスケット / 最大ガスケット面圧 / 三次元有限要素法 / ボルト / 軸力管理 / 弾性相互作用 |
|---|
| Research Abstract |
1.Optimal Tightening Procedure of Pipe Flange Connections
Introducing "Elastic Interaction Coefficient Method" into 3-D FEA, two numerical methods have been proposed, which can estimate the scatter of bolt preloads when tightening the clamping bolts with an arbitrary sequence and provide an optimal tightening sequence that gives uniform bolt preloads in the final state.
2.Mechanical Behaviors of Pipe Flange Connections using Soft Gaskets
By incorporating the stress strain relationship of asbestos joint sheet gasket that were obtained experimentally into FE analysis, an optimal tightening sequence, mechanical behaviors under external loads and its sealing performance have been analyzed systematically.
3.Elucidation of Mechanical Properties of the Disassembly Process of Pipe Flange Connections
Variations of bolt clamping forces and contact pressure distributions on the gasket interface have been systematically analyzed using FE approach developed above.
4.Proposal of a Robust Tightening Proced
… More
ure of Pipe Flange Connections
To suppress the scatter in final bolt clamping forces, an effective tightening sequence is to clamp the four bolts simultaneously, which are apart ninety degrees each other, and then tighten the other bolts simply in the clockwise pattern.
5.Effects of Short Bolt Clamping Force on the Sealing Performance of Pipe Flange Connections
It has been found that the missing of two bolts causes 1.6 times initial clamping force in the remaining bolts in the case of 20 inch flanges.
6.Relationship between the scatter in bolt preloads and gasket contact stresses from the view point of sealing performance
The scatter due to torque control method is found to be fairly smaller than that due to the elastic interaction of bolt deformations caused by the successive tightening operation.
7.Evaluation Procedure of Leakage Performance based on Computational Mechanics
It has been shown that the leakage rate can be estimated by means of the maximum contact stress occurred along the outer diameter of gasket.
A part of the achievements of this study has been published from High Pressure Institute of Japan (HPI) as "A Guideline for Pipe Flange Tightening. Z103TR-2004". Less
|
