| Project/Area Number |
63045018
|
|---|
| Research Category |
Grant-in-Aid for international Scientific Research
|
| Allocation Type | Single-year Grants |
|---|
| Section | University-to-University Cooperative Research |
|---|
| Research Institution | Kyoto Institute of Technology |
|---|
Principal Investigator |
SOEN Toshiichi (1990) Professor, Dept. of Polymer Science and Engineering, Kyoto Institute of Technology, 繊維学部, 教授 (10025984)
宗円 寿一 (1989-1990) 京都工芸繊維大学, 繊維学部, 教授
宗圓 寿一 (1988) 京都工芸繊維大, 繊維, 教授
|
|---|
| Co-Investigator(Kenkyū-buntansha) |
CAKMAK Miko Associate Professor, Polymer Engineering Center, the University of Akron, USA, 高分子工学センター(アメリカ合衆国), 副教授
MIN Kyonsuku Assistant Professor, Polymer Engineering Center, the University of Akron, USA, 高分子工学センター(アメリカ合衆国), 助教授
KYU Thein Associate Professor, Polymer Engineering Center, the University of Akron, USA, 高分子工学センター(アメリカ合衆国), 副教授
WHITE James L. Director, Professor, Polymer Engineering Center, the University of Akron, USA, 高分子工学センター(アメリカ合衆国), 所長
YAMANE Hideki Instructor, Dept. of Polymer Science and Engineering, Kyoto Institute of Technol, 繊維学部, 助手 (30191365)
NISHIMURA Taro Associate Professor, Cooperative Research Center, Kyoto Institute of Technology, 地域共同研究センター, 助教授 (30027883)
KITAO Toshio Professor, Dept. of Polymer Science and Engineering, Kyoto Institute of Technolo, 繊維学部, 教授 (70027879)
|
|---|
| Project Period (FY) |
1988 – 1990
|
| Project Status |
Completed (Fiscal Year 1990)
|
| Budget Amount *help |
¥7,400,000 (Direct Cost: ¥7,400,000)
Fiscal Year 1990: ¥2,500,000 (Direct Cost: ¥2,500,000)
Fiscal Year 1989: ¥2,500,000 (Direct Cost: ¥2,500,000)
Fiscal Year 1988: ¥2,400,000 (Direct Cost: ¥2,400,000)
|
|---|
| Keywords | Polymer Blends / Blending Process / Blending Machine / Morphology of Blends / Mechanical Properties |
|---|
| Research Abstract |
This Research Project intended to develope "Studies on Blending Process, Blend Morphology and Mechanical Properties of Polymer Blends" in cooperation with Polymer Engineering Center at the University of Akron (APEC), USA.
In the term of this project, we could invite 9 investigators in total from APEC, and 15 Japanese investigators, including members out of this project, visited to APEC for cooperative research.
This research was performed by the above investigators in charge of following four subjects separately and/or cooperatively.
(1) Study on blending machine and blending process.
This subject was researched at APEC as J. L. White et al. Designed and constructed new blending machine already in APEC. Kitao et al. Carried materials which prepared in Kyoto Institute of Technology (KIT), and blended them by the machine (Twin Screw Extruder) and carried back to KIT and the morphology and mechanical properties of the blends were observes at KIT.
(2) Measurement and analysis of morphology of b
… More
lends.
This subject was also researched at APEC as T. Kyu have good instruments to observe the blends morphology. Our graduate student H. Takahashi visited to study under direction of T. Kyu. He carried materials to APEC and investigated their phase separation kinetics.
(3) Measurement and analysis of mechanical properties of blends.
Our graduate studeny I. Nishimura visited to APEC and made rubber blends and carried back to KIT, and measured and analized their mechanical properties at KIT using a specially designed instrument under the direction of T. Soen et al.
(4) Developement of computer programs to make the data-base relating blending compounds, blends morphology and practical properties of blends.
This subject was researched at KIT under the direction of T. Soen et al. That is, using the results obtaited on subject (3) and their practical properties like as strength at breakage, elongation at breakage, hardness, reboundness, wet skid index etc. were stored onto the data-base and analyzed by the factor analysis method. Less
|
