| Project/Area Number |
16360362
|
|---|
| Research Category |
Grant-in-Aid for Scientific Research (B)
|
| Allocation Type | Single-year Grants |
|---|
| Section | 一般 |
|---|
| Research Field |
Material processing/treatments
|
|---|
| Research Institution | Nagoya University (2006)
Tokyo Institute of Technology (2004-2005) |
|---|
Principal Investigator |
OHTAKE Naoto Nagoya University, Dept. of Materials, Physics and Energy Engineering, Associate Professor, 大学院工学研究科, 助教授 (40213756)
|
|---|
| Co-Investigator(Kenkyū-buntansha) |
YASUHARA Toshiyuki Tokyo Institute of Technology, Dept. of Mechanical Sciences and Engineering, Assistant Professor, 大学院理工学研究科, 助手 (70282829)
MITSUDA Yoshitaka The University of Tokyo, Institute of Industrial Science, Professor, 生産技術研究所, 教授 (20212235)
|
|---|
| Project Period (FY) |
2004 – 2006
|
| Project Status |
Completed (Fiscal Year 2006)
|
| Budget Amount *help |
¥11,200,000 (Direct Cost: ¥11,200,000)
Fiscal Year 2006: ¥2,900,000 (Direct Cost: ¥2,900,000)
Fiscal Year 2005: ¥2,600,000 (Direct Cost: ¥2,600,000)
Fiscal Year 2004: ¥5,700,000 (Direct Cost: ¥5,700,000)
|
|---|
| Keywords | Carbon nanotube / Nano material / Injection Molding / Materials Processing / Mechanics of Materials / 機械材料・材料力学 / カーボンナノチューブ / 複合材料 / ナノコンポジット / ナノ材料試験 / 強度 / 表面処理 / DLC / 押出し |
|---|
| Research Abstract |
Carbon nanotubes (CNTs) are expected to be one of the most promising nano-materials for improving mechanical properties as well as electrical properties of polymer matrix composites. However, since the size of CNTs is on the nanometer order, there are little reports about the experimental evaluation of their properties by direct manipulation, which is performed in a scanning electron microscope (SEM), an atomic force microscope (AFM). In the material design for using nano-materials, it is essential to understand the characteristics of nano-materials experimentally. We attempted to measure Young's modulus of various types of CNTs. A cantilever, which is usually used for an AFM and made of silicon, was mounted on the piezo-driving stage. The apparent Young's modulus of the CNT is calculated from the conventional relationship between the load applied to the CNT and the displacement of the tip of the CNT. Five types of CNTs are used in the series of experiments. They are ARC-CNTs, CVD-CNTs
… More
, two types of Vapor-grown CNTs (VGCNTs); named VG80 and VG50, which are 80nm and 50nm in average diameters, respectively. The relative intensities ratio of the D-band around 1350 cm^<-1> to the G-band around 1580 cm^<-1>(ID/IG) in Raman spectra was obtained using the Gaussian fitting. An ARC-CNT was bent like a bending beam by a lateral force applied by a tip of the cantilever. For calculating the apparent Young's modulus of CNT, an equation for the conventional bending beam was applied. Since Young's modulus actually calculated includes the influence of the section modulus and indicates the flexural rigidity, it was termed "apparent Young's modulus". The apparent Young's modulus of the ARC-CNT used here was obtained as 3.3 TPa. This value is slightly lower than the theoretical Young's modulus (5.5 TPa) of the single-walled CNT, which was simulated using molecular dynamics. The same measurements and calculation were performed on other CNTs, and the relationship between the apparent Young's modulus obtained from TEM measurements and the ID/IG obtained from the Raman spectra is summarized. The result clearly shows that the high-crystallinity CNT has a high apparent Young's modulus.
Next, we studied injection molding of MWCNT filled polystyrene (PS) and evaluation of the mechanical and electrical properties comparing with the composites in which conventional carbon fillers were filled. As a result, the resistivity of the composites filled with CNT drops significantly between 3 and 4 vol.% and after which it decreases linearly above 4 vol.%. The resistivity of the composites filled with CNT is 1.2x10^2 W・cm when the CNT concentration is 11.6 vol.%. The resistivity is significantly lower than that of the composites which were filled with conventional carbon fillers. The elastic modulus slightly improves with increasing CNT concentration The tensile strength is almost constant in the pristine CNT concentration range from 0 to 12 vol.%. Then we applied DLC coating and amino-functionalization of CNTs and found that the tensile strength increases up to 20% using the functionalized CNTs in PP matrix. Less
|
