| 研究課題/領域番号 |
23K19191
|
|---|
| 研究種目 |
研究活動スタート支援
|
| 配分区分 | 基金 |
|---|
| 審査区分 |
0401:材料工学、化学工学およびその関連分野
|
|---|
| 研究機関 | 国立研究開発法人産業技術総合研究所 |
|---|
研究代表者 |
Park Kwangjae 国立研究開発法人産業技術総合研究所, 材料・化学領域, 研究員 (50980893)
|
|---|
| 研究期間 (年度) |
2023-08-31 – 2025-03-31
|
| 研究課題ステータス |
交付 (2023年度)
|
| 配分額 *注記 |
2,860千円 (直接経費: 2,200千円、間接経費: 660千円)
2024年度: 1,430千円 (直接経費: 1,100千円、間接経費: 330千円)
2023年度: 1,430千円 (直接経費: 1,100千円、間接経費: 330千円)
|
|---|
| キーワード | ARB process / nanocomposite magnet / Sm-Co alloy / permanent magnet / roll bonding |
|---|
| 研究開始時の研究の概要 |
While the possibility of nanocomposite magnets as a next-generation permanent magnet that exceeds the performance of single-phase permanent magnets is still in the spotlight, the realization of successful NC magnets is still a long way off due to difficulties in realizing the ideal microstructure. In this study, the applicant aims to pave the way for the realization of NC bulk magnets by forming the nano-laminate microstructures using magnetic nanopowders and the accumulative roll-bonding process.
|
| 研究実績の概要 |
In this study, the ARB process was improved the prepare the non-oxidized bulk laminate for realizing the NC bulk magnet. As a preliminary experiment, the Cu/Fe/Cu/Co/Cu starting materials were selected for demonstrating the laminated microstructure. The nanoscale-controlled layered microstructure with about 40~100 nm was partially achieved. The Nd-Fe-B material prepared by strip casting was used to prepare the bulk laminate. The laminated Nd-Cu microstructure was achieved by ARB pross. Based on these results, it is assumed that the new developed ARB process have possibility for realizing the nanoscale-controlled microstructure in the NC bulk magnet.
|
| 現在までの達成度 (区分) |
現在までの達成度 (区分)
3: やや遅れている
理由
It took some time to maintenance the ARB equipment to allow the ARB process in a low oxygen atmosphere. And it was quite difficult to find the proper process temperature for the ARB process because the RE alloys and TM metals are easy to react to alloying other unfavorable phases. In addition, the preparation of magnet laminate by the ARB process was quite challenge because the brittleness of the RE alloys. Therefore, for these reasons, it took a long time to establish initial process conditions.
|
| 今後の研究の推進方策 |
Based on the previous preliminary work, the possibility of ARB process for realizing the nanoscale-controlled microstructure was confirmed. The Sm-Co thin plate and Fe-Co plate are used as starting materials. Future plan is the investigation of the mechanism of nano-layered texture formation during the ARB process according to the pre-heating temperature. Since the RE alloys are very easy to react with the TM metals over about 600C, it is necessary to find the proper pre-heating temperature for preparing the laminate bulk magnet. In addition, the experimental demonstration of the effective coupling length from the thickness of nano-layered Fe and magnetic properties will be progressed.
|
